Unilift AP35B.50.06.3.VZanurzeniowa pompa do ściekówPionowa jednostopniowa zanurzeniowa pompa ze stali nierdzewnej zintegrowana z 3-fazowym silnikiem zanurzeniowym. Pompa jest wyposażona w pierścień podstawy i uchwyt nośny oraz dostarczana jest wraz z przewodem sieciowym o długości 5 m. Wirnik to wirnik VORTEX o swobodzie przepływu 35 mm, odpowiedni do pompowania wody powierzchniowej, wód gruntowych, ścieków i podobnych cieczy.Pompa ma podwójne uszczelnienie wału i pośrednią komorę olejową wypełnioną nietoksycznym specjalnym olejem. Silnik ma klasę izolacji F i posiada długotrwałe smarowane na całe życie głębokie rowkowe łożyska kulkowe.Pompa ma port odpływu R2 'i jest gotowa do instalacji zarówno wolnostojącej, jak iw systemie samoczynnego sprzęgania.Ciecz:Maksymalna temperatura cieczy:40 ° CTechniczne:Typ wirnika:VORTEXMaksymalny rozmiar cząstek:35 mmMateriały:Obudowa pompy:Stal nierdzewna Obudowa pompy:DIN W.-Nr.1.4301 Obudowa pompy:AISI 304Wirnik:Stal nierdzewna Wirnik:DIN W.-Nr.1.4301 Wirnik:AISI 304Instalacja:Wylot pompy:R2 'Maksymalna głębokość instalacji:7 mDane elektryczne:Moc wejściowa - P1:1 kW Napięcie znamionowe:3 x 400 V Prąd znamionowy:1,55 A Cos phi - współczynnik mocy :0,89 Znamionowa prędkość obrotowa :2830 obr / min Klasa ochrony (IEC 34-5):IP68 Klasa izolacji (IEC 85):F Długość kabla :5 m Typ wtyku kablowego:NONE Inne:Waga netto :8,22 kg

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 65-120 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

3-stopniowa, zanurzalna pompa zaprojektowana do zaopatrywania w wodę domową, transferu cieczy w zbiornikach, nawadniania i aplikacji środowiskowych. Pompa ma pływające wirniki, każdy z własnym łożyskiem wolframowo-karbadowym/ceramicznym.

Produkt mobilny do hydronicznego wyważania grzejników w połączeniu z pompą ALPHA3 i smartfonem z zainstalowaną aplikacją "Go Balance", która jest dostępna dla urządzeń iOS i Android. Do tymczasowego montażu na pompie ALPHA3

Unilift CC 7 Grundfos Unilift CC pumps are single-stage submersible pumps with a low suction ability down to 3 mm water level.The pumps are designed for pumping rainwater and grey wastewater, e.g. from• washing machines, baths, sinks, etc. from low-lying parts of buildings up to sewer level• cellars or buildings prone to flooding• draining wells• wells for surface water with inlets from roof gutters, pits, tunnels, etc.• swimming pools, ponds or fountains.The pumps are suitable for both stationary and portable use.They are for automatic operation.The pumps allow free passage of particles up to ø10 mm.The motor incorporates automatic overload protection cutting out the motor in case of overload.When cooled to normal temperature, the motor restarts automatically.Technical:Maximum particle size:10 mmMaterials:Pump housing:PP 15 GFImpeller:PPOm 20 GFInstallation:Pump outlet:1.1/4'Maximum installation depth:10 mLiquid:Liquid temperature range:0 .. 40 °CElectrical data:Rated voltage:1 x 220-240 VRated current:1.8 ACapacitor size - run:8 F/450 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:10 mType of cable plug:SCHUKOOthers:Net weight:4.6 kgGross weight:5.2 kgShipping volume:0.168 m3

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

UP 15-14 BA PMThe high efficiency Coomfort PM range is a product for domestic hotwater recirculation in 1 and 2 family houses.The motor is a single-phase, 2-pole, hysteresis, permanent-magnet motor in conformity with the EMCdirective.Characteristics and benefits:* Unique AUTOADAPT saves up to 50% heatenergy and 87% motor energy compared with a standard pump in continuous operation* Flushing function* Automatic legionella operation (if supported from the system)* Automatic weekend and vacation function* Temperature control optional* Continuous operation optional* Fast and simple electrical installation due to the million times trusted ALPHA plug* Easy to clean and lime insensitive spheric rotor* Application area up 14°dH water hardness* Wearless operation due to liquid lubricated bearing* No leakage risk due to a static seal* Easy maintenance and cleaning by easy-to-separated motor head that fits on all standard circulation pump housings* Korrosion resistant pump housing in brass* Due to impedance protected motor no motor protection necessary* No additional installation costs due to integrated non return and stop valve in the pump housingLiquid:Liquid temperature range:2 .. 95 °CTechnical:TF class:95Approvals on nameplate:VDE,GS,CEMaterials:Pump housing:Brass MS 68Impeller:Stainless steel, EPDM, PPO, PTFE, GraphitInstallation:Maximum operating pressure:10 barPipe connection:Rp 1/2Port-to-port length:80 mmElectrical data:Max. power input:8 WRated voltage:1 x 230 VCurrent in speed 3:0.07 ACapacitor size - run:0.6 FEnclosure class (IEC 34-5):IP44Insulation class (IEC 85):FOthers:Net weight:1 kgGross weight:1.12 kgShipping volume:0.003 m3

MAGNA3 40-80 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remote

MAGNA3 40-120 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

ALPHA2 jest w stanie wytrzymać trudne warunki w systemie grzewczym, a dzięki czterem nowo dodanym funkcjom stał się jeszcze bardziej wytrzymały:Robust start-up: Wstrząsa wolne od zanieczyszczeń przed rozpoczęciem sezonu grzewczego.Lato mode:Dostosowanie wydajności pompy do temperatury na zewnątrz latem - zapewniając klientom dodatkową efektywność energetyczną.Odporność magnetytowa: Zapewnia, że ​​żadne małe kawałki metalu nie utkną w ważnych częściach pompy, gdy zostaną namagnesowane.Ochrona przed suchobiegiem: Upewnij się, że pompa nigdy nie działa bez płynu w systemie - dodaj do tego bezkonkurencyjną efektywność energetyczną, łatwą instalację i fakt, że ALPHA2 pokrywa zarówno Twoje wymagania dotyczące ogrzewania, jak i do 90% Twoich wymagań dotyczących klimatyzacji i chłodzenia. GRUNDFOS ALPHA2 nadaje się do:Systemów o stałym lub zmieniającym się przepływieJednorurkowe systemyDwu-rurowe systemyOgrzewanie podłogoweRecyrkulacja ciepłej wody użytkowejSystemy wymagające nocnego obniżenia temperatury.Funkcje i korzyści• Lepsza wydajność przy wiodącej na rynku efektywności (EEI0.15) w bardziej kompaktowym designie• Nowy miernik przepływu do rozwiązywania problemów i balansowania• AUTOADAPT wybiera najlepszą krzywą wydajności dla efektywności i komfortu• Innowacyjny wtyk upraszcza połączenie pompy• W zestawie są osłony izolacyjne.

Unilift CC 5 Grundfos Unilift CC pumps are single-stage submersible pumps with a low suction ability down to 3 mm water level.The pumps are designed for pumping rainwater and grey wastewater, e.g. from• washing machines, baths, sinks, etc. from low-lying parts of buildings up to sewer level• cellars or buildings prone to flooding• draining wells• wells for surface water with inlets from roof gutters, pits, tunnels, etc.• swimming pools, ponds or fountains.The pumps are suitable for both stationary and portable use.They are for automatic operation.The pumps allow free passage of particles up to ø10 mm.The motor incorporates automatic overload protection cutting out the motor in case of overload.When cooled to normal temperature, the motor restarts automatically.Technical:Maximum particle size:10 mmMaterials:Pump housing:PP 15 GFImpeller:PPOm 20 GFInstallation:Pump outlet:1.1/4'Maximum installation depth:10 mLiquid:Liquid temperature range:0 .. 40 °CElectrical data:Rated voltage:1 x 220-240 VRated current:0.98 ACapacitor size - run:4 F/450 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):BLength of cable:5 mType of cable plug:SCHUKOOthers:Net weight:4.35 kgGross weight:5 kgShipping volume:0.168 m3

Unilift AP35.40.06.A1.VSubmersible drainage pump typeVertical single-stage stainless steel submersiblepump with vertical discharge port and integratedsubmersible 1-phase totally enclosed motorin insulation class F with thermal overloadprotection. The pump is fitted with suction strainer and level switch for automatic start and stop.The impeller is a VORTEX impeller for35 mm free passage suitable for pumpinggroundwater, surface water, rain water andsimilar.The pump has a double shaft seal and anintermediate oil chamber pre-filled with non-toxicspecial oil.The pump has a riser pipe, a cooling jacket for continuous cooling of the motor by the pumped liquid and long-life deep-groove greased-for-life ball bearings.The pump is ready for use as it is fitted withcarrying handle and is supplied with a10 m mains cable. The mains cable is ofthe plug type with glass sealing compound in thesocket to prevent penetration of humidity intothe stator windings.Liquid:Liquid temperature range:0 .. 55 °CTechnical:Type of impeller:VORTEXMaximum particle size:35 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4301Impeller:AISI 304Installation:Pump outlet:Rp 1 1/2Maximum installation depth:10 mElectrical data:Type of motor:PSCPower input - P1:0.9 kWRated voltage:1 x 230 VRated current:4 ACos phi - power factor:0,97Rated speed:2810 rpmCapacitor size - run:16 F/400 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:10 mType of cable plug SchukoOthers:Net weight:11.4 kgGross weight:11.9 kg

Nazwa produktu: Podpórka kablowa dla 2 pływaków

ALPHA2 jest w stanie wytrzymać trudne warunki w systemie grzewczym, a dzięki czterem nowo dodanym funkcjom stał się jeszcze bardziej wytrzymały:Robust start-up: Wstrząsa wolne od zanieczyszczeń przed rozpoczęciem sezonu grzewczego.Lato tryb:Dostosowanie wydajności pompy do temperatury na zewnątrz latem - zapewniając klientom dodatkową efektywność energetyczną.Odporność magnetytu: Zapewnia, że ​​żadne małe kawałki metalu nie utkną w ważnych częściach pompy, gdy zostaną namagnesowane.Ochrona przed suchobiegiem: Upewnij się, że pompa nigdy nie działa bez płynu w systemie - dodaj do tego bezkonkurencyjną efektywność energetyczną, łatwą instalację i fakt, że ALPHA2 pokrywa zarówno Twoje wymagania dotyczące ogrzewania, jak i do 90% Twoich wymagań dotyczących klimatyzacji i chłodzenia. GRUNDFOS ALPHA2 nadaje się do:Systemów o stałym lub zmieniającym się przepływieJednorurkowe systemyDwu-rurowe systemyOgrzewanie podłogoweRecyrkulacja ciepłej wody użytkowejSystemy wymagające nocnego obniżenia temperatury.Funkcje i korzyści• Lepsza wydajność przy wiodącej na rynku efektywności (EEI0.15) w bardziej kompaktowym designie• Nowy miernik przepływu do rozwiązywania problemów i balansowania• AUTOADAPT wybiera najlepszą krzywą wydajności dla efektywności i komfortu• Innowacyjny wtyk upraszcza połączenie pompy• W zestawie są osłony izolacyjne.

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 65-60 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remote

Unilift KP 250 M 1Submersible drainage pumpVertical single-stage stainless steel submersiblepump with vertical discharge port and integratedsubmersible 1-phase canned motor ininsulation class F with thermal overloadprotection. The pump is fitted with a suction strainer, acarrying handle and is supplied with a 10 mmains cable.The impeller is a semi-open impeller for 10 mmfree passage suitable for pumping groundwater,surface water, rain water and similar liquids.The pump has a double shaft seal consisting oftwo lip seals with grease in-between.The pump has an outer casing ensuring continuouscooling of the motor by the pumped liquid.The rotor shaft operates in two maintenance-freecarbon bearings cooled by the pumped liquidThe motor is filled with a non-toxic motor liquid.Liquid:Liquid temperature range:0 .. 50 °CTechnical:Maximum particle size:10 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4031Impeller:AISI 304Installation:Pump outlet:Rp 1 1/4Maximum installation depth:10 mElectrical data:Power input - P1:480 WRated voltage:1 x 220-230 VRated current:2.3 ACapacitor size - run:8 F/400 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:10 mType of cable plug SchukoOthers:Net weight:7 kgGross weight:7.3 kgShipping volume:0.013 m3

MAGNA3 32-120 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

GRUNDFOS GO MI301The Grundfos GO Remote is used to establish wireless connection to a Grundfos product, using a standard Android or iOS platform, with the Grundfos GO Remote App installed. The App is available from Apple App Store and Google Play free of charge.The MI 301 is a module with built-in infrared and radio communication. It must be used in conjunction with an Android or iOS-based Smartphone with Bluetooth connection. The MI 301 module has rechargeable Li-ion battery and must be charged separately.The pump/system can be monitoried and controlled from the Grundfos GO, and it will be possible to create pdf reports. The specific functions available depend on each individual product.Supplied with the product•Grundfos MI 301•Battery charger•Quickguide.Installation:Range of ambient temperature:70 .. -20 °CRelative humidity:95 %Electrical data:Maximum current consumption:0.03 AEnclosure class (IEC 34-5):IP40

Unilift KP 350 A 1Submersible drainage pumpVertical single-stage stainless steel submersiblepump with vertical discharge port and integratedsubmersible 1-phase canned motor ininsulation class F with thermal overloadprotection. The pump is fitted with suction strainer and acarrying handle and is supplied with a 10 mmains cable and float switch for automatic startand stop.The impeller is a semi-open impeller for 10 mmfree passage suitable for pumping groundwater,surface water, rain water and similar liquids.The pump has a double shaft seal consisting oftwo lip seals with grease in-between.The pump has an outer casing ensuring continuouscooling of the motor by the pumped liquid.The rotor shaft operates in two maintenance-freecarbon bearings cooled by the pumped liquid.The motor is filled with a non-toxic motor liquid. Liquid:Liquid temperature range:0 .. 50 °CTechnical:Maximum particle size:10 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4031Impeller:AISI 304Installation:Pump outlet:Rp 1 1/4Maximum installation depth:10 mElectrical data:Power input - P1:700 WRated voltage:1 x 220-240 VRated current:3.2 ACapacitor size - run:8 F/400 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:10 mType of cable plug: SchukoOthers:Net weight:8 kgGross weight:8.3 kgShipping volume:0.013 m3

ALPHA2 jest w stanie wytrzymać trudne warunki w systemie grzewczym, a dzięki czterem nowo dodanym funkcjom stał się jeszcze bardziej wytrzymały:Robust start-up: Wstrząsa wolne od zanieczyszczeń przed rozpoczęciem sezonu grzewczego.Lato tryb:Dostosowanie wydajności pompy latem do cieplejszej temperatury na zewnątrz - dając klientom dodatkową efektywność energetyczną.Magnetite resistance: Zapewnia, że ​​żadne małe kawałki metalu nie utkną w ważnych częściach pompy, gdy zostaną namagnesowane.Ochrona przed suchobiegiem: Upewnij się, że pompa nigdy nie działa bez płynu w systemie - dodaj do tego bezkonkurencyjną efektywność energetyczną, łatwy montaż i fakt, że ALPHA2 pokrywa zarówno Twoje wymagania dotyczące ogrzewania, jak i do 90% Twoich wymagań dotyczących klimatyzacji i chłodzenia.GRUNDFOS ALPHA2 nadaje się do:Systemów o stałym lub zmieniającym się przepływieJednorurkowe systemyDwururowe systemyOgrzewanie podłogoweRecyrkulacja ciepłej wody użytkowejSystemy wymagające nocnego obniżenia temperatury.Funkcje i korzyści• Lepsza wydajność przy najwyższej efektywności rynkowej (EEI0.15) w bardziej kompaktowym designie• Nowy miernik przepływu do rozwiązywania problemów i balansowania• AUTOADAPT wybiera najlepszą krzywą wydajności dla efektywności i komfortu• Innowacyjny wtyk upraszcza połączenie pompy• W zestawie osłony izolacyjne.

Grundfos Unilift CC pumps are single-stage submersible pumps with a low suction ability down to 3 mm water level. The pumps are designed for pumping rainwater and grey wastewater, e.g. from •washing machines, baths, sinks, etc. from low-lying parts of buildings up to sewer level•cellars or buildings prone to flooding•draining wells•wells for surface water with inlets from roof gutters, pits, tunnels, etc.•swimming pools, ponds or fountains.The pumps are suitable for both stationary and portable use. They are for automatic operation. The pumps allow free passage of particles up to ø10 mm. The motor incorporates automatic overload protection cutting out the motor in case of overload. When cooled to normal temperature, the motor restarts automatically. Technical: Maximum particle size: 10 mm Materials: Pump housing: PP 15 GF Impeller: PPOm 20 GF Installation: Pump outlet: 1.1/4 Maximum installation depth: 10 m Liquid: Pumped liquid: Any Newtonian liquid Liquid temperature range: 0 .. 40 °C Density: 998.2 kg/m3 Electrical data: Mains frequency: 50 Hz Rated voltage: 1 x 220-240 V Rated current: 1.8 A Capacitor size - run: 8 F/450 V Enclosure class (IEC 34-5): IP68 Insulation class (IEC 85): F Length of cable: 10 m Type of cable plug: SCHUKO

Unilift AP50B.50.11.3.VZanurzeniowa pompa do ściekówPionowa jednostopniowa zanurzeniowa pompa ze stali nierdzewnej z wbudowanym trójfazowym silnikiem zanurzeniowym. Pompa jest wyposażona w pierścień podstawowy i uchwyt nośny oraz dostarczana jest z przewodem sieciowym o długości 5 m. Wirnik to wirnik VORTEX o swobodzie przepływu 50 mm, odpowiedni do pompowania wody powierzchniowej, wód gruntowych, ścieków i podobnych cieczy.Pompa ma podwójne uszczelnienie wału i pośrednią komorę olejową wypełnioną nietoksycznym specjalnym olejem. Silnik ma klasę izolacji F i posiada długotrwałe smarowane na całe życie łożyska kulkowe głębokiego rowka.Pompa ma port odpływu R 2' i jest gotowa do instalacji zarówno samodzielnie jak i na systemie samoczynnego sprzęgania.Ciecz:Maksymalna temperatura cieczy:40 °CTechniczne:Typ wirnika:VORTEXMaksymalny rozmiar cząstek:50 mmMateriały:Obudowa pompy:Stal nierdzewna Obudowa pompy:DIN W.-Nr. 1.4301 Obudowa pompy:AISI 304 Wirnik:Stal nierdzewna Wirnik:DIN W.-Nr. 1.4301 Wirnik:AISI 304Instalacja:Wylot pompy:R 2' Maksymalna głębokość instalacji:7 mDane elektryczne:Moc wejściowa - P1:1,75 kWNapięcie znamionowe:3 x 400 VPrąd znamionowy:2,81 ACos phi - współczynnik mocy :0,90Znamionowa prędkość obrotowa :2785 obr./min.Klasa ochrony (IEC 34-5):IP68 Klasa izolacji (IEC 85):F Długość kabla :5 m Typ wtyku kablowego:NONE Inne:Waga netto :10,6 kg