Pompy - strona 2

Unilift AP35.40.06.A1.VSubmersible drainage pump typeVertical single-stage stainless steel submersiblepump with vertical discharge port and integratedsubmersible 1-phase totally enclosed motorin insulation class F with thermal overloadprotection. The pump is fitted with suction strainer and level switch for automatic start and stop.The impeller is a VORTEX impeller for35 mm free passage suitable for pumpinggroundwater, surface water, rain water andsimilar.The pump has a double shaft seal and anintermediate oil chamber pre-filled with non-toxicspecial oil.The pump has a riser pipe, a cooling jacket for continuous cooling of the motor by the pumped liquid and long-life deep-groove greased-for-life ball bearings.The pump is ready for use as it is fitted withcarrying handle and is supplied with a10 m mains cable. The mains cable is ofthe plug type with glass sealing compound in thesocket to prevent penetration of humidity intothe stator windings.Liquid:Liquid temperature range:0 .. 55 °CTechnical:Type of impeller:VORTEXMaximum particle size:35 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4301Impeller:AISI 304Installation:Pump outlet:Rp 1 1/2Maximum installation depth:10 mElectrical data:Type of motor:PSCPower input - P1:0.9 kWRated voltage:1 x 230 VRated current:4 ACos phi - power factor:0,97Rated speed:2810 rpmCapacitor size - run:16 F/400 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:10 mType of cable plug SchukoOthers:Net weight:11.4 kgGross weight:11.9 kg

SOLOLIFT2 C-3Sololift2 C-3 is a small, compact automatic lifting station suitable for pumping of greywater (w/o faeces) off places in private dwellings where wastewater cannot be led directly to the sewer by means of a natural downward slope.Sololift2 C-3 is typically used for:• cabinet showers, washbasins, bath tubs, washing machines (max. 90°C) and dishwashers in basements below sewer level or in connection with the renovation or modernisation of existing buildings, where the location may be remote from the main soil pipe so that a natural slope cannot be established.Sololift2 C-3 is suitable for installation under a washbasin or particularly for confined space conditions in prewall constructions and built-in cabinets. Extremely low switching levels for lowest construction heights, advantageously in case of connection of a shower receptor.The compact lifting station is equipped with- Cable with or without plug (see technical data)- Horizontal or vertical faste

Zestaw adapterów cpl. DN 40-PN10 30mm

MAGNA3 50-120 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

Pump for Water in one family houses

Pump for Water in one family houses

3-stopniowa, zanurzalna pompa zaprojektowana do zaopatrywania w wodę domową, transferu cieczy w zbiornikach, nawadniania i aplikacji środowiskowych. Pompa ma pływające wirniki, każdy z własnym łożyskiem wolframowo-karbadowym/ceramicznym.

Produkt mobilny do hydronicznego wyważania grzejników w połączeniu z pompą ALPHA3 i smartfonem z zainstalowaną aplikacją "Go Balance", która jest dostępna dla urządzeń iOS i Android. Do tymczasowego montażu na pompie ALPHA3

Salus EP Electronic A-class circulation pump for heating systems and other non-corrosive liquids, ensuring high comfort and low energy consumption.The EP circulation pump is mainly used for water circulation in home heating, and is best suited for the following system:• Stable heating system with variable flow• Heating system with variable pipeline temperature• Industrial circulation system• House and apartment heating systemsThe EP circulation pump can adjust the electric pump's performance automatically and continuously to meet the actual needs of the systemThe EP circulation pump is equipped with a control panel on the front, which is convenient for users. Easy installation and startupEP circulation pump has automatic adaptation mode AUTO (factory setting). In most cases, you can start the pump without making any adjustments and let it automatically adjust to meet the actual needs of the system. High comfortThe operating noise of the pump is low. Low energy consumptionCompared to the conventional circulation pump, its energy consumption is very low. The minimum energy consumption for the EP circulation pump can reach 5 W.EP circulation pump does not need external motor protection. Check whether the voltage and frequency of the power supply correspond to the parameters indicated on the pump nameplate. Use the pump's corresponding connector to connect the power supply (EPPLUG).

Dzięki ALPHA2 GO instalator może teraz wymienić większość wszystkich samodzielnych pomp obiegowych oraz prawie 70% pomp zintegrowanych z węzłami ciepłowniczymi, kotłami gazowymi i pompami ciepła po 2015 roku. Wymiary montażowe: 180mm

Gardena 2000/2 2 bar 2000 l/h

Zestaw adapterów cpl. DN 50-PN10 40mm

Pompa drenażowa Grundfos Unilift AP Basic 35B.50.06.A1.V to model Grundfos Unilift AP Basic przeznaczony do zastosowań jako pompa drenażowa, pompa do ścieków oraz pompa dla wykonawców.

Ten produkt jest określony jako afløbspumpe, tłumaczone jako pompa drenażowa, z zachowaniem dokładnego oznaczenia modelu 35B.50.06.A1.V bez zmian dla precyzyjnego wyboru.

Praktyczna opcja przy dopasowywaniu konkretnej pompy drenażowej Grundfos Unilift AP Basic do wymaganej kategorii pomp.

SOLOLIFT2 D-2Sololift2 D-2 is a small, compact automatic lifting station suitable for pumping of wastewater off places in private dwellings where greywater (w/o faeces) cannot be led directly to the sewer by means of a natural downward slope.Sololift2 D-2 is typically used for:• cabinet showers, washbasins or bidets in basements below sewer level, in connection with the renovation or modernisation of existing buildings, where the location may be remote from the main soil pipe so that a natural slope cannot be established.Extremely low switching levels for lowest construction heights, advantageously in case of connection of a shower receptor.Sololift2 D-2 is suitable for confined space conditions in built-in cabinets or also below shower receptors or pedestals.The pumping of liquids containing other material may cause faults and limit the scope of our guarantee.The compact lifting station is equipped with- Cable with or without plug (see technical data)- Disc

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 50-60 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remote

Kit, shaft seal H QQEGG KB016S1 30 bar

Sparepart for Vortex

Wygodne, gdy nie ma dostępnej gniazdka AC. Łatwe do przenoszenia dzięki kompaktowej i lekkiej konstrukcji. Długi czas pracy wynoszący 50 minut z baterią 5,0 Ah. Wbudowany metalowy filtr siatkowy zapobiega wyciekowi oleju pompy próżniowej z portu wydechowego. Port odpływowy z zaworem. Zawór zapobiega cofaniu się oleju.

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

Salus EP Electronic A-class circulation pump for heating systems and other non-corrosive liquids, ensuring high comfort and low energy consumption.The EP circulation pump is mainly used for water circulation in home heating, and is best suited for the following system:• Stable heating system with variable flow• Heating system with variable pipeline temperature• Industrial circulation system• House and apartment heating systemsThe EP circulation pump can adjust the electric pump's performance automatically and continuously to meet the actual needs of the systemThe EP circulation pump is equipped with a control panel on the front, which is convenient for users. Easy installation and startupEP circulation pump has automatic adaptation mode AUTO (factory setting). In most cases, you can start the pump without making any adjustments and let it automatically adjust to meet the actual needs of the system. High comfortThe operating noise of the pump is low. Low energy consumptionCompared to the conventional circulation pump, its energy consumption is very low. The minimum energy consumption for the EP circulation pump can reach 5 W.EP circulation pump does not need external motor protection. Check whether the voltage and frequency of the power supply correspond to the parameters indicated on the pump nameplate. Use the pump's corresponding connector to connect the power supply (EPPLUG).

Unilift AP35B.50.06.3.VZanurzeniowa pompa do ściekówPionowa jednostopniowa zanurzeniowa pompa ze stali nierdzewnej zintegrowana z 3-fazowym silnikiem zanurzeniowym. Pompa jest wyposażona w pierścień podstawy i uchwyt nośny oraz dostarczana jest wraz z przewodem sieciowym o długości 5 m. Wirnik to wirnik VORTEX o swobodzie przepływu 35 mm, odpowiedni do pompowania wody powierzchniowej, wód gruntowych, ścieków i podobnych cieczy.Pompa ma podwójne uszczelnienie wału i pośrednią komorę olejową wypełnioną nietoksycznym specjalnym olejem. Silnik ma klasę izolacji F i posiada długotrwałe smarowane na całe życie głębokie rowkowe łożyska kulkowe.Pompa ma port odpływu R2 'i jest gotowa do instalacji zarówno wolnostojącej, jak iw systemie samoczynnego sprzęgania.Ciecz:Maksymalna temperatura cieczy:40 ° CTechniczne:Typ wirnika:VORTEXMaksymalny rozmiar cząstek:35 mmMateriały:Obudowa pompy:Stal nierdzewna Obudowa pompy:DIN W.-Nr.1.4301 Obudowa pompy:AISI 304Wirnik:Stal nierdzewna Wirnik:DIN W.-Nr.1.4301 Wirnik:AISI 304Instalacja:Wylot pompy:R2 'Maksymalna głębokość instalacji:7 mDane elektryczne:Moc wejściowa - P1:1 kW Napięcie znamionowe:3 x 400 V Prąd znamionowy:1,55 A Cos phi - współczynnik mocy :0,89 Znamionowa prędkość obrotowa :2830 obr / min Klasa ochrony (IEC 34-5):IP68 Klasa izolacji (IEC 85):F Długość kabla :5 m Typ wtyku kablowego:NONE Inne:Waga netto :8,22 kg

Sparepart for Vortex

Smedegaard Simflex 25-60 1x230V 180 mm pompa obiegowa 112.